www.mywifiext.net wn1000rp is also known as a Wireless Repeater that helps to boost up the internet speed of the existing WiFi network coverage. Netgear wn1000rp manual is the WiFi booster for mobile devices so that the users can enjoy the improved wireless experience on their Android tablets, iPads, netbooks, Smartphones, and e-readers, etc. It supports all security standards including WEP, WPA=PSK, WPA2-PSK, and mixed-mode.
Even, you can connect www.mywifiext.net wn1000rp with the scanners and printers. The configuration process of this range extender is quite simple and easy but keeps the wireless router, the Netgear Wn1000rp, and wireless device in the same room to avoid further wireless interference. When you purchase this product, you will get the Manual Guide. Just follow the instruction mentioned in the Manual Guide to get a stable connection.
Features of Netgear Wifi Extender wn1000rp Setup
- Helps to eliminate the WiFi dead zone areas
- Reduces 3G or 4G mobile data usage
- Compatible with Windows 8
- Repeats 2.4 GHz WiFi Signal
- Push ‘N’ Connect option provides a secured connection to the connected devices
- WiFi Booster for mobile devices
Easy Methods for Netgear wn1000rp Manual
We are going to discuss the most appropriate methods of setting up Netgear Wn1000rp WiFi Range Extender. There are two methods to set up the Netgear Wn1000rp Extender.
WPS (WiFi Protected Setup) Method
WPS is a wireless network security standard that establishes a connection between a WiFi-enabled device and a WiFi router. When the users connect both devices, they will get a fast and secure connection. To set up the Netgear wn1000rp manual, you need to execute the following steps:
- Firstly, checks whether your WiFi router supports WPS or not. If not, then use the browser setup method.
- If yes, then attach your Netgear wn1000rp manual to the power outlet.
- Switch on the extender by pressing the “Power On/off” button that is situated on the side panel.
- Wait till the “Status” light to illuminate green.
- With 1-2 minutes, press and hold the WPS button on the wireless router.
- Once the connection between the main wireless router and the range extender is established, the “Link Rate” LED will illuminate.
- Now, your WiFi range extender is ready to use so that you can connect your devices to it.
- Once the wireless device is connected to the Netgear Wn1000rp, the “WiFi Device to Booster” light will turn on.
Netgear wn1000rp Manual Method
The users can simply configure the Netgear Wn1000rp Setup by just using a Web Browser. To proceed with the Netgear Wn1000rp Extender Setup, you need to perform the following steps:
- Give the power supply to your range extender. When the WiFi Booster is switched on and the Status LED is green, use a wireless network manager on your system.
- Find and connect to the SSID (NETGEAR_EXT) wireless network.
- After the connection is established with the wireless device, the “WiFi Device to Booster” LED converts to solid green.
- Now, connect the WiFi Booster (Wn1000rp Extender) to your existing WiFi network.
- Launch the web browser from the same connected wireless device, and type the local web address (mywifiext.net) in the address bar.
- It will take you to the on-screen setup guide.
- Choose the main wireless router SSID and hit on the “Continue” tab.
- Type the network key/passphrase in the password filed and clicks on the “Continue” button.
- Next, select the extender settings. Here, the users can modify the SSID and the wireless passphrase or can use the same security settings of the existing network. Click Continue.
- After changes, hit on the “Apply Settings” option to save the changes.
- Connect the WiFi-enabled devices to the newly created wireless network. Once the WiFi-enabled device is connected, choose “My wireless devices are connected to the Extender Network” option and hit “Continue”.
- Finally, click on the “Finish” button and attempt to access the internet.
Reset Instructions for Netgear Wn1000rp
If the Wn1000rp Extender is not working properly, not being responsive or dropping connections. The users can reset the Netgear Wn1000rp in the following ways:
With the Reset Button
- Switch on the extender and wait for one minute for it to load, if booted.
- Then, pick a paper clip or sharp pen. With it, press down the “Restore Factory Settings” button and hold it for 7-8 seconds.
- When the power light begins to blink, release the “Reset” button and wait till the extender restart.
- Once the range extender is started, the power light will be stable (not blinking).
The 30-30-30 Reset
If the above method does not work, you can try the 30-30-30 reset method that is discussed below:
- Firstly, turn on your Wn1000rp Range Extender.
- Press the “Reset” button with the help of a paper clip or something sharp and hold it for 30 seconds.
- While holding the pressed “Reset” button, unplug the power of the range extender and still hold the “Reset” button for 30 seconds.
- While still holding the button, supply the power to the extender again and hold for another 30 seconds.
- Finally, this procedure usually works for resetting your WiFi extender to its default factory settings.
How to Login to the Netgear Wn1000rp WiFi Range Extender
- Ensure that the range extender is connected to the router’s network, either by Ethernet cable or WiFi.
- Open the web browser and visit the mywifiext.net or 192.168.1.250 default IP address
- This address link will be prompted to the login dialogue.
- Here, enter the default login credentials – username as “admin” and the password as “password”. But if you have already changed the password then use it.
- Now, click on the “Login” tab. After successfully logged into it, we recommend that change the default password, if not changed earlier.
- You will be able to view or change the settings of your extender according to your requirements.
But these instructions are not applicable for your router. You can do it with factory reset to get the default settings or try some other common Netgear credentials.